Re: Poor NUMA balance and high %RDY after latest patches - ESXi 5.0 build...
Thanks Jon We have Intel E5-26xx series procs, and are currently evaluating this patch release. Have a case open with Vmware asking them to confirm whether this patch impacts performance on recent...
View ArticleRe: Purpose of VMware Tools in a Linux guest?
JarryG, that's a useful link. I'd actually read 70% of the docs but missed that section!
View Articleadd existing vmdk with new-HardDisk doesent work with 2008R2VM...
Hello together, there is a very strange behavior.I want to add a drive from a Windows Server 2003 VM to an Windows Server 2008R VM. I use this New-HardDisk -VM $vm -DiskPath "[storage1]...
View ArticleRe: Can a Wyse V10L frmw 6.4.0_24 connect to a View 5.1 desktop ?
Hi LucD, can you post the link of the post?
View ArticleRe: Migration 5.1.1 High Cpu
I`m allmost considering a rollback to ESXi 5.0U2... but with VMware Virtual Center 5.1u1aI think this is a issue from the Virtual Machine HW-layer 9 with ESXi5.1U1, accoording to the different stories...
View ArticleVmware View + C10LE WTOS + VDI Broker Initialization failed
Hi, I'm a noob in regards to VMware view and C10 client. We are trying to setup the Win7 VMware View of our client to run to our C10LE and we are receiving "VDI Broker Initialization failed" and when...
View ArticleRe: add existing vmdk with new-HardDisk doesent work with 2008R2VM...
And which PowerCLI version are you using ?Can you do aGet-PowerCLIVersion
View ArticleRe: add existing vmdk with new-HardDisk doesent work with 2008R2VM...
ahh sorry: VMware vSphere PowerCLI 4.0 U1 build 208462
View ArticleRe: add existing vmdk with new-HardDisk doesent work with 2008R2VM...
Ouch, that's an older version (3.5 years). And it doesn't seem to support W2K8R2, see the 4.0.1 Release Notes. Any chance of upgrading to the latest ?The latest build supports ESXi 4 Update 4, see the...
View ArticleRe: Guest USB device not getting enough power
Hi, you can use an Y-cable to get more power for your USB device. I had the same problem with a card-reader and a cable like this was the...
View ArticleHorizon View 5.2 new install, protocol failure on desktops
On a new Horizon View 5.2 deployment, I'm experiencing a "Protocol failure" status on all provisioned desktops. I have not enabled or installed HTML5 access, but in the debug log file of the virtual...
View ArticleRe: Guest connected but cannot RDP to it
Is there any antivirus installed that might be the cause?Did you try to RDP from guest to host ? (of course you will have to enable and configure RDP also)
View ArticleRe: add existing vmdk with new-HardDisk doesent work with 2008R2VM...
I just have to update the local Powercli Vresion on my wokstation/maintain VM(?)That should be done until eobd.
View ArticleClik here to view.
Re: Can a Wyse V10L frmw 6.4.0_24 connect to a View 5.1 desktop ?
It was indirect evidence The post was Configuring Dell Wyse ThinOS™ Thin Clients with Dell vWorkspace
View ArticleRe: ESXi vm sees physical CPU's : Activation issue
Is there any way to use some sort of 'generic CPU' in the VM,so that I can avoid future reactivation when I move the VM? Thanks!Thomas.
View ArticleRe: Vcenter DR setup
I don't think you do something like this if u dont have SRM. May be if you enable FT and put your secondary VMs on new site
View ArticleRe: add existing vmdk with new-HardDisk doesent work with 2008R2VM...
That is correct, but watch out, if you're using pre-ESXi 4 Update 4 systems, you might run into other problems.
View ArticleRe: VCOPS EMC VNX Connector License
EMC provided me an eval license for the EMC Storage Analytics product. As you stated, the license key is required when configuring the VNX Block device, so it's stands to reason the license key comes...
View ArticleRe: Configure Network Management Grey Out
Just do Reset Networking, then add NICs and Restart the Management Agents. Make sure the cable is attached to the NIC/NICs.
View Article